Setting tool instrument with one fixed and one mobile part.Acting on the mobile part with the tool, the dial indicator gives the measurement variation.Suitable for use on machine tools to check the exact length of the...
WORKSHOP DIGITAL INDICATOR 325
Workshop digital indicator. Digital display LCD, height of digits 8,5 mm. mm/inch conversion. Setting to zero in any position. Measuring pin in hardened and ground stainless steel. Clamping: stem ø 8 – h6 in hardened and ground stainless steel. Interchangeable contact point M2,5. Powered with one battery. With serial number. Manufactured as per internal rule. Supplied in case.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0325
Love0
Add to compare0
20 other products in the same category:
Dial test indicator. Sylvac digital electronic components with out-put OPTO RS232 (enable the direct connection to PC). “0” setting function – mm/inch conversion – change of reading – min/max selection. Dial diameter...
Test indicator. Ruby-mounted gear movements give maximum precision but the test indicator is also shockproof. Automatic inversion of the direction of measurement without a switch to anticlockwise direction of the...
Thickness gauge in cast aluminium for easy use.Digital reading.Different contact points available.Contact “C” are supplied as standard.Set to zero by rotating the dial bezel.
Test indicator.Ruby-mounted gear movements give maximum precision but the test indicator is also shockproof.Automatic inversion of the direction of measurement without a switch to anticlockwise direction of the...
High quality digital indicators. Sylvac digital electronic components with output OPTO RS232 (enable the direct connection to PC).“0” setting function – mm/inch conversion – hold (memory) – REF I/REF II – PRESET...
Non-magnetic stainless steel flat bridge for quick and easy depth measurament.Suppiled in case with anticlockwise dial indicator.Available upon requirement: digital indicator.Art. 322 base hardened stainless steel.
Quick thickness gauge for external measurements, wall thickness and external grooves.Knife points.Transmission of thickness value via steel wire.Supplied in case.
High precision bore gauges indicated for the detection of ovality and taper.Particularly cared for in the transmission of movement.Hardened steel contacts.Chromed steel body with insulating handle.Built according to...
Bore gauges with hardened steel contact surfaces for small bores.The travel on the contact surfaces is trasmitted via a needle in hardened steel a 1:1 ration.Interchangeable ogive in hardened steel, heat-insulated...
Test indicator.Ruby-mounted gear movements give maximum precision but the test indicator is also shockproof.Automatic inversion of the direction of measurement without a switch to anticlockwise direction of the...
Quick thickness gauge for internal diameters and internal grooves.Transmission of thickness value via steel wire.Supplied in case.
Shockproof and waterproof dial indicator.Insulation against water and dust in the most delicate areas.Rubber casing to protect the spindle and rack.The upper part of the dial indicator is insulated by protective...
Error free dial gauge, shockproof, with over travel.Due to its high-class compact protection the safety dial gaude offers an extremely long service life.A gear rack sleeve covering the length of the spindle is...
Range of shorter bore gauges with contact points in hardened steel.Body in chromed stel with heat-insulated grip.Manufactured as per DIN 878.Supplied in case without dial indicator.Art. 5272 version with carbide...
ACCESSORIES FOR METRIC DIAL TEST INDICATORS
Saw setting dial indicator.Two-sided readout allows measurement of teeth of circular and other saws.Flat contact surfaces in hard metal.Supplied in case.
English
Italiano 
