Tempered stainless steel cap square.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with serial number.Built according to DIN 875/0 standard.Supplied...
ART.0382 - PRECISION STRAIGHT EDGE IN NON-DEFORMABLE STEEL, WITH GRADUATION
Millimeter control line in non-deformable steel.
Rectified on all faces.
Engraved precision graduation, easy to read, durable over time.
Equipped serial number.
Built according to DIN 874/1 and DIN 866/1 standards.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0382
Love0
Add to compare0
20 other products in the same category:
Sliding square in non-deformable steel with anti-corrosion treatment.Suitable for the transfer of angles.
elbow team for flange in non -deformable steel with antibody treatment. entirely rectified on the faces.
Simple bevelled square in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground.High precision being performed and tested according to...
Simple square in non-deformable steel.Completely ground on the faces.High precision being performed with tight tolerances.Built according to DIN 875/1 standard.
Art. 420 built according to the DIN 875/2 standard.
PDF TAB
Square with striker and bevel in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.Entirely ground, of high precision being performed and tested according to restricted...
Bevelled steel ruler with one millimetre graduation.Ground on all faces. Etched, precision graduation, easy to read and long-lasting. Serial number.Manufactured as per DIN 866/1.
High precision square with internal bevelled edge.Made of hardened stainless steel.Built according to DIN 875/00 standard.Supplied in scabbard.
PDF TAB
Temperatured stainless steel control ruler.Suitable for high precision checks.Rectified on all sides.With handle and section for << I >> for stability and lightness.Equipped with serial number.Built...
Set square with cap in non-hardened stainless steel.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with number serial number.Built according to DIN...
45° square with stock in non-deformable steel.Entirely ground surfaces.Manufactured as per DIN 875/2.
Rulers with contraction in mat stainless steel.Division on one side, etched, easy to read and long-lasting.Contractions: 0,5% - 0,8% - 1,25% - 1,5% - 1,7% - 1.75% - 1,8% - 2% - 2,25% - 3% - 4% - 6%.Please specify the...
Flat 135° square in non-deformable steel. Entirely ground surfaces. Manufactured as per DIN 875/2.
Simple square in non-deformable chromed steel.The square is covered with a uniform layer of hard chrome applied with a special procedure which ensures a high degree of hardness and protection to the surfaces from...
Square with 135° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Hardened stainless steel knife-edge straight edge for fast and precise control of planarity and parallelism.Made from hardened stainless steel, ground with lapped contact angle.Fitted with heat-insulated...
High precision plane-parallel control ruler in black granite.Two parallel, plane, lapped faces with << I >> -shaped section for stability and lightness.The parallelism tolerance is equal to the planarity...
Square with 120° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Angle plate made from G25 perlitic cast iron with T-grooves. Compact and stabilised structure. Closely scraped work surfaces. Manufactured as per DIN 875/3.
high precision team in stainless steel timing. Complete with square row with 45 ° chamtoe in super-rapid cobalt steel. 65. Suitable for matrici corrector . built according to DIN 875/0. supplied in the case....
English
Italiano 
![](http://pinterest.com/pin/create/button/?url=https%3A%2F%2Fwww.bocchicontrol.it%2Fen%2Fcontrol-rulers-and-squares%2F319-art0517-square-in-cast-iron-with-t-grooves.html&description=ART.0517 - SQUARE IN CAST IRON WITH "T"-GROOVES&media=https://www.bocchicontrol.it/567-large_default/art0517-square-in-cast-iron-with-t-grooves.jpg){kind=link}
