Semi-rigid rulers in mat stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
ART.0381 - PRECISION STRAIGHT EDGE IN STAINLESS STEEL
Temperatured stainless steel control ruler.
Suitable for high precision checks.
Rectified on all sides.
With handle and section for << I >> for stability and lightness.
Equipped with serial number.
Built according to DIN 874/1 standard.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0381
Love0
Add to compare0
20 other products in the same category:
Square with 120° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Parallel block in stabilized G26 pearlitic cast iron.Fine planed working surface.
Simple square in non-deformable steel.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment.< br...
Simple square in non-deformable steel.Completely ground on the faces.High precision being performed with tight tolerances.Built according to DIN 875/1 standard.
Art. 420 built according to the DIN 875/2 standard.
PDF TAB
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Square with stock in non-deformable steel.Entirely ground faces.High precision.Made to strict tolerances.Manufactured as per DIN 875/1.
Item 421 manufactured as per DIN 875/2.
Bevelled square with hardened stainless steel cap.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground. High precision as it is manufactured and tested according to...
Square in harendened stainless steel.Large section for greater precision.Ground on all sides.Serial number.Manufactured as per DIN 875/0.Suppilied in case.
High precision square with internal bevelled edge.Made of hardened stainless steel.Built according to DIN 875/00 standard.Supplied in scabbard.
PDF TAB
Black granite inspection square, suitable for perpendicularity checks.Highly reliable instrument, thanks to very narrow tolerances and support stability.Lightning holes are drilled on the large squares.The surfaces...
Flexible rulers in mat stainless steel. Division on one side only, etched, easy to read and long-lasting. Manufactured as per DIN 866/2. Particular divisions and numberings available upon requirement.
Assembly box with T-grooves and slots.Made in G25 stabilised perlitic cast iron.Squareness between the scraped faces to DIN 875/3 precision.T-grooves and slots as per UNI 4788.
Simple square in non-deformable chromed steel.The square is covered with a uniform layer of hard chrome applied with a special procedure which ensures a high degree of hardness and protection to the surfaces from...
Periphery tape in steel for round bodies.The instrument has two scales: the upper one is for diameters and the lower for circumferences.
Square with tempered stainless steel striker.Completely ground, of high precision as it is performed and tested according to restricted procedures.The serial number is engraved which guarantees its traceability.Built...
Parallel square in non-deformable steel with anti-corrosion treatment.The stop is hardened to reduce wear to the minimum.The entire beam is graduated in millimeters with long-lasting incision.A reference line is...
Square with 60° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Simple steel square with anti-corrosion galvanic treatment.Being machined from solid, it allows for two 45° angles and one 90°.Entirely ground surfaces.
English
Italiano 
