Square with 120° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
ART.0456 - SQUARE 50X25 MM WITH BEAM 5X5X65 MM
High precision square in hardened stainless steel.
Complete with 45º bevelled edge beam in super-rapid cobalt steel.
Ground and hardened to HRC 64-65.
Suitable for a mould checker.
Manufactured as per DIN 875/0.
Supplied in case.
Complete with 45º bevelled edge beam in super-rapid cobalt steel.
Ground and hardened to HRC 64-65.
Suitable for a mould checker.
Manufactured as per DIN 875/0.
Supplied in case.
Attention: for the interchangeable shaped beams, see Item 72/455 from the Code 02.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0456
Love0
Add to compare0
20 other products in the same category:
Precision straight edge in non-deformable steel made to very small tolerances; for precision control situations.Ground on all faces.Serial number.Manufactured as per DIN 874/1.
Millimeter control line in non-deformable steel.Rectified on all faces.Engraved precision graduation, easy to read, durable over time.Equipped serial number.Built according to DIN 874/1 and DIN 866/1 standards.
PDF TAB
Simple square in hardened stainless steel.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with serial number.Built according to DIN 875/0...
Simple bevelled square in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground.High precision being performed and tested according to...
High precision square with 30° and 45° bevelled edge.Body and edge in hardened stainless steel.Suitable for for metric corrector.Built according to DIN 875/0 standard.Supplied in case.
PDF TAB
Steel ruler with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.Cod. 10 total length 1000 mm as master of length.
Square with non-deformable steel leaf.Entirely ground on the faces, of high precision being performed with restricted tolerances.Built according to the DN 875/1 standard.
Square with non-deformable steel hat.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment. Built with...
Simple 45° square in non-deformable steel.Entirely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Simple steel square with anti-corrosion galvanic treatment.Being machined from solid, it allows for two 45° angles and one 90°.Entirely ground surfaces.
Flexible rulers in mat stainless steel. Division on one side only, etched, easy to read and long-lasting. Manufactured as per DIN 866/2. Particular divisions and numberings available upon requirement.
Bevelled square with hardened stainless steel cap.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground. High precision as it is manufactured and tested according to...
High precision square in hardened stainless steel.Complete with adjustable round rule.In 64÷ hardened cobalt super-rapid steel 65 HRC.Suitable for matrix corrector.Manufactured according to DIN 875/0 standard.Supplied...
Onglet square in non-deformable steel.With anti-corrosion treatment.This square is equipped with several degrees: in fact, it is possible to measure 90° - 45° - 30° - 120°.Fully ground on the surfaces.Built according...
Square with stock in non-deformable steel.Entirely ground faces.High precision.Made to strict tolerances.Manufactured as per DIN 875/1.
Item 421 manufactured as per DIN 875/2.
Square with 135° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Square with non-deformable steel cap.The base made from a single piece and not applied, makes this square very sturdy and suitable for heavy carpentry work.A galvanic treatment protects it from possible oxidation.
PDF...
Tempered stainless steel cap square.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with serial number.Built according to DIN 875/0 standard.Supplied...
team of high precision in stainless steel. Complete with square row with 45 ° chamtoe in super-rapid cobalt steel.Rectified and timing HRC 64 ÷ 65. Suitable for matrici corrector.Built according to DIN 875/0...
English
Italiano 
