Angle detector and bisector.Consisting of an adjustable part in which, by means of a line of faith and an engraved and easy-to-read graduated rod, it can be detected or set the desired angle and a removable part...
ART.0441 - SQUARE WITH KNOCK AND BEVEL
Square with striker and bevel in hardened stainless steel.
The two chamfered and lapped sides allow for a more accurate visual check.
Entirely ground, of high precision being performed and tested according to restricted procedures.
The serial number is engraved to guarantee traceability.
Built according to DN 875/00 standard.
Supplied in case.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0441
Love0
Add to compare0
20 other products in the same category:
Simple 45° square in non-deformable steel.Entirely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Set square with cap in non-hardened stainless steel.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with number serial number.Built according to DIN...
Simple square in non-deformable chromed steel.The square is covered with a uniform layer of hard chrome applied with a special procedure which ensures a high degree of hardness and protection to the surfaces from...
Flat 135° square in non-deformable steel. Entirely ground surfaces. Manufactured as per DIN 875/2.
Bevelled square with hardened stainless steel cap.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground. High precision as it is manufactured and tested according to...
Periphery tape small section in steel for round bodies.The instrument has two scales: the upper one is for diameters and the lower for circumferences.
Bevelled steel ruler with one millimetre graduation.Ground on all faces. Etched, precision graduation, easy to read and long-lasting. Serial number.Manufactured as per DIN 866/1.
High precision square in hardened stainless steel.Complete with adjustable round rule.In 64÷ hardened cobalt super-rapid steel 65 HRC.Suitable for matrix corrector.Manufactured according to DIN 875/0 standard.Supplied...
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Steel ruler with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.Cod. 10 total length 1000 mm as master of length.
Precision straight edge in non-deformable steel made to very small tolerances; for precision control situations.Ground on all faces.Serial number.Manufactured as per DIN 874/1.
High precision square in hardened stainless steel.Complete with 45º bevelled edge beam in super-rapid cobalt steel.Ground and hardened to HRC 64-65.Suitable for a mould checker.Manufactured as per DIN 875/0.Supplied...
Periphery tape in steel for round bodies.The instrument has two scales: the upper one is for diameters and the lower for circumferences.
G25 pearlitic cast iron square.Compact and stabilized structure.Fine planed work surfaces.
PDF TAB
Square with non-deformable steel hat.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment. Built with...
Simple steel square with anti-corrosion galvanic treatment.Being machined from solid, it allows for two 45° angles and one 90°.Entirely ground surfaces.
High precision square with 30° and 45° bevelled edge.Body and edge in hardened stainless steel.Suitable for for metric corrector.Built according to DIN 875/0 standard.Supplied in case.
PDF TAB
Square with 135° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Square with 60° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
English
Italiano 
