Adjustable square with slot that allows greater adherence to the piece.Made of non-deformable steel with galvanic anti-corrosion treatment.Suitable for applying corners.
ART.0080 - ANGLE AND BISETRIX MEASURING INSTRUMENT
Angle detector and bisector.
Consisting of an adjustable part in which, by means of a line of faith and an engraved and easy-to-read graduated rod, it can be detected or set the desired angle and a removable part (bevel) which determines the bisector of the angle previously measured or set.
This last part, removable, therefore becomes a useful element for tracing two pieces to join or for orient cutting machines (cutters, shears, etc.).
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0080
Love0
Add to compare0
20 other products in the same category:
Square with 60° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Simple 45° square in non-deformable steel.Entirely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Rulers with contraction in mat stainless steel.Division on one side, etched, easy to read and long-lasting.Contractions: 0,5% - 0,8% - 1,25% - 1,5% - 1,7% - 1.75% - 1,8% - 2% - 2,25% - 3% - 4% - 6%.Please specify the...
Square with non-deformable steel hat.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment. Built with...
Millimeter control line in non-deformable steel.Rectified on all faces.Engraved precision graduation, easy to read, durable over time.Equipped serial number.Built according to DIN 874/1 and DIN 866/1 standards.
PDF TAB
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Simple bevelled square in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground.High precision being performed and tested according to...
Flat 135° square in non-deformable steel. Entirely ground surfaces. Manufactured as per DIN 875/2.
Periphery tape small section in steel for round bodies.The instrument has two scales: the upper one is for diameters and the lower for circumferences.
Cube for radial drills in stabilized G26 pearlitic cast iron.Properly ribbed to ensure strength.Fine planed working surface with “T” grooves.
High precision square in hardened stainless steel.Complete with adjustable round rule.In 64÷ hardened cobalt super-rapid steel 65 HRC.Suitable for matrix corrector.Manufactured according to DIN 875/0 standard.Supplied...
High precision plane-parallel control ruler in black granite.Two parallel, plane, lapped faces with << I >> -shaped section for stability and lightness.The parallelism tolerance is equal to the planarity...
Semi-rigid rulers in mat stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Steel ruler with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.Cod. 10 total length 1000 mm as master of length.
Simple square in non-deformable steel.Completely ground on the faces.High precision being performed with tight tolerances.Built according to DIN 875/1 standard.
Art. 420 built according to the DIN 875/2 standard.
PDF TAB
team of high precision in stainless steel. Complete with square row with 45 ° chamtoe in super-rapid cobalt steel.Rectified and timing HRC 64 ÷ 65. Suitable for matrici corrector.Built according to DIN 875/0...
Ruler in non-deformable steel with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.
Simple 60° square in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
Square with non-deformable steel cap.The base made from a single piece and not applied, makes this square very sturdy and suitable for heavy carpentry work.A galvanic treatment protects it from possible oxidation.
PDF...
English
Italiano 
