Onglet square in non-deformable steel.With anti-corrosion treatment.This square is equipped with several degrees: in fact, it is possible to measure 90° - 45° - 30° - 120°.Fully ground on the surfaces.Built according...
ART.0507 - SLIDING SQUARE WITH SLOT
Adjustable square with slot that allows greater adherence to the piece.
Made of non-deformable steel with galvanic anti-corrosion treatment.
Suitable for applying corners.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0507
Love0
Add to compare0
20 other products in the same category:
High precision square with 30° and 45° bevelled edge.Body and edge in hardened stainless steel.Suitable for for metric corrector.Built according to DIN 875/0 standard.Supplied in case.
PDF TAB
Bevelled square with hardened stainless steel cap.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground. High precision as it is manufactured and tested according to...
High precision square in hardened stainless steel.Complete with adjustable rule.In cobalt super-fast steel, ground and HRC hardened 64÷ 65.Provided with angle reading indicator in degrees from –10° / 0° /...
45° square with stock in non-deformable steel.Entirely ground surfaces.Manufactured as per DIN 875/2.
Square with 135° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Simple 60° square in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
Cube for radial drills in stabilized G26 pearlitic cast iron.Properly ribbed to ensure strength.Fine planed working surface with “T” grooves.
Angle plate made from G25 perlitic cast iron with T-grooves. Compact and stabilised structure. Closely scraped work surfaces. Manufactured as per DIN 875/3.
Simple steel square with anti-corrosion galvanic treatment.Being machined from solid, it allows for two 45° angles and one 90°.Entirely ground surfaces.
Set square with cap in non-hardened stainless steel.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with number serial number.Built according to DIN...
high precision team in stainless steel timing. Complete with square row with 45 ° chamtoe in super-rapid cobalt steel. 65. Suitable for matrici corrector . built according to DIN 875/0. supplied in the case....
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Flat 135° square in non-deformable steel. Entirely ground surfaces. Manufactured as per DIN 875/2.
Simple square in non-deformable chromed steel.The square is covered with a uniform layer of hard chrome applied with a special procedure which ensures a high degree of hardness and protection to the surfaces from...
Bevelled steel ruler with one millimetre graduation.Ground on all faces. Etched, precision graduation, easy to read and long-lasting. Serial number.Manufactured as per DIN 866/1.
Square with non-deformable steel leaf.Entirely ground on the faces, of high precision being performed with restricted tolerances.Built according to the DN 875/1 standard.
Simple square in non-deformable steel.Completely ground on the faces.High precision being performed with tight tolerances.Built according to DIN 875/1 standard.
Art. 420 built according to the DIN 875/2 standard.
PDF TAB
flat and adjustable magnetic teams .
are indispensable for welding or tracks where a 90 ° position is needed.
Black granite inspection square, suitable for perpendicularity checks.Highly reliable instrument, thanks to very narrow tolerances and support stability.Lightning holes are drilled on the large squares.The surfaces...
English
Italiano 
![](http://pinterest.com/pin/create/button/?url=https%3A%2F%2Fwww.bocchicontrol.it%2Fen%2Fcontrol-rulers-and-squares%2F319-art0517-square-in-cast-iron-with-t-grooves.html&description=ART.0517 - SQUARE IN CAST IRON WITH "T"-GROOVES&media=https://www.bocchicontrol.it/567-large_default/art0517-square-in-cast-iron-with-t-grooves.jpg){kind=link}
