Square with non-deformable steel leaf.Entirely ground on the faces, of high precision being performed with restricted tolerances.Built according to the DN 875/1 standard.
ART.0475 - FLAT 45° SQUARE
Simple 45° square in non-deformable steel.
Entirely ground on the surfaces.
Built according to DIN 875/2 standard.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0475
Brand:
Love0
Add to compare0
20 other products in the same category:
Temperatured stainless steel control ruler.Suitable for high precision checks.Rectified on all sides.With handle and section for << I >> for stability and lightness.Equipped with serial number.Built...
Tempered stainless steel cap square.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with serial number.Built according to DIN 875/0 standard.Supplied...
Simple square in non-deformable steel.Completely ground on the faces.High precision being performed with tight tolerances.Built according to DIN 875/1 standard.
Art. 420 built according to the DIN 875/2 standard.
PDF TAB
Simple 120° square in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Square with striker and bevel in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.Entirely ground, of high precision being performed and tested according to restricted...
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
High precision square in hardened stainless steel.Complete with adjustable round rule.In 64÷ hardened cobalt super-rapid steel 65 HRC.Suitable for matrix corrector.Manufactured according to DIN 875/0 standard.Supplied...
Bevelled ruler in non-deformable steel with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.
Centering square in non-deformable steel with anti-corrosion treatment.Allows rapid centering of discs and shafts, tracking, 45° and 90° control.The whole scale is graduated in millimeters with long-lasting...
Square with 60° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Onglet square in non-deformable steel.With anti-corrosion treatment.This square is equipped with several degrees: in fact, it is possible to measure 90° - 45° - 30° - 120°.Fully ground on the surfaces.Built according...
Simple set square in non-hardened stainless steel.Fully ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with a number of serial number.Built according to DIN...
Simple square in non-deformable steel.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment.< br...
Parallel square in non-deformable steel with anti-corrosion treatment.The stop is hardened to reduce wear to the minimum.The entire beam is graduated in millimeters with long-lasting incision.A reference line is...
Simple square in hardened stainless steel.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with serial number.Built according to DIN 875/0...
Bevelled square with hardened stainless steel cap.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground. High precision as it is manufactured and tested according to...
Square with stock in non-deformable steel.Entirely ground faces.High precision.Made to strict tolerances.Manufactured as per DIN 875/1.
Item 421 manufactured as per DIN 875/2.
Bait Guardapiano at 5 blades. Suitable for corrector matrices . in stainless steel, rectified and lapping. built According to DIN 874/0. provided in the case.
PDF TAB
Square with non-deformable steel hat.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment. Built with...
English
Italiano 
