Parallel square in non-deformable steel with anti-corrosion treatment.The stop is hardened to reduce wear to the minimum.The entire beam is graduated in millimeters with long-lasting incision.A reference line is...
ART.0450 - ONGLET SQUARE
Onglet square in non-deformable steel.
With anti-corrosion treatment.
This square is equipped with several degrees: in fact, it is possible to measure 90° - 45° - 30° - 120°.
Fully ground on the surfaces.
Built according to DIN 875/2 standard.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0450
Love0
Add to compare0
20 other products in the same category:
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Centering square in non-deformable steel with anti-corrosion treatment.Allows rapid centering of discs and shafts, tracking, 45° and 90° control.The whole scale is graduated in millimeters with long-lasting...
Sliding square in non-deformable steel with anti-corrosion treatment.Suitable for the transfer of angles.
High precision square with 30° and 45° bevelled edge.Body and edge in hardened stainless steel.Suitable for for metric corrector.Built according to DIN 875/0 standard.Supplied in case.
PDF TAB
Square with non-deformable steel hat.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment. Built with...
High precision square with internal bevelled edge.Made of hardened stainless steel.Built according to DIN 875/00 standard.Supplied in scabbard.
PDF TAB
High precision square in hardened stainless steel.Complete with adjustable round rule.In 64÷ hardened cobalt super-rapid steel 65 HRC.Suitable for matrix corrector.Manufactured according to DIN 875/0 standard.Supplied...
high precision team in stainless steel timing. Complete with square row with 45 ° chamtoe in super-rapid cobalt steel. 65. Suitable for matrici corrector . built according to DIN 875/0. supplied in the case....
Simple bevelled square in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground.High precision being performed and tested according to...
Precision straight edge in non-deformable steel made to very small tolerances; for precision control situations.Ground on all faces.Serial number.Manufactured as per DIN 874/1.
Hardened stainless steel knife-edge straight edge for fast and precise control of planarity and parallelism.Made from hardened stainless steel, ground with lapped contact angle.Fitted with heat-insulated...
Simple square in non-deformable chromed steel.The square is covered with a uniform layer of hard chrome applied with a special procedure which ensures a high degree of hardness and protection to the surfaces from...
Periphery tape in steel for round bodies.The instrument has two scales: the upper one is for diameters and the lower for circumferences.
Black granite inspection square, suitable for perpendicularity checks.Highly reliable instrument, thanks to very narrow tolerances and support stability.Lightning holes are drilled on the large squares.The surfaces...
High precision plane-parallel control ruler in black granite.Two parallel, plane, lapped faces with << I >> -shaped section for stability and lightness.The parallelism tolerance is equal to the planarity...
Simple steel square with anti-corrosion galvanic treatment.Being machined from solid, it allows for two 45° angles and one 90°.Entirely ground surfaces.
Rulers with contraction in mat stainless steel.Division on one side, etched, easy to read and long-lasting.Contractions: 0,5% - 0,8% - 1,25% - 1,5% - 1,7% - 1.75% - 1,8% - 2% - 2,25% - 3% - 4% - 6%.Please specify the...
Periphery tape small section in steel for round bodies.The instrument has two scales: the upper one is for diameters and the lower for circumferences.
English
Italiano 
