Simple bevelled square in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground.High precision being performed and tested according to...
ART.0505 - CENTRING SQUARE
Centering square in non-deformable steel with anti-corrosion treatment.
Allows rapid centering of discs and shafts, tracking, 45° and 90° control.
The whole scale is graduated in millimeters with long-lasting engraving.
With serial number.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0505
Love0
Add to compare0
20 other products in the same category:
Millimeter control line in non-deformable steel.Rectified on all faces.Engraved precision graduation, easy to read, durable over time.Equipped serial number.Built according to DIN 874/1 and DIN 866/1 standards.
PDF TAB
Square with tempered stainless steel striker.Completely ground, of high precision as it is performed and tested according to restricted procedures.The serial number is engraved which guarantees its traceability.Built...
Simple square in non-deformable steel.Completely ground on the faces.High precision being performed with tight tolerances.Built according to DIN 875/1 standard.
Art. 420 built according to the DIN 875/2 standard.
PDF TAB
High precision square in hardened stainless steel.Complete with 45º bevelled edge beam in super-rapid cobalt steel.Ground and hardened to HRC 64-65.Suitable for a mould checker.Manufactured as per DIN 875/0.Supplied...
Steel ruler with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.Cod. 10 total length 1000 mm as master of length.
Square with non-deformable steel hat.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment. Built with...
Flat 135° square in non-deformable steel. Entirely ground surfaces. Manufactured as per DIN 875/2.
Adjustable square with slot that allows greater adherence to the piece.Made of non-deformable steel with galvanic anti-corrosion treatment.Suitable for applying corners.
Simple steel square with anti-corrosion galvanic treatment.Being machined from solid, it allows for two 45° angles and one 90°.Entirely ground surfaces.
Simple set square in non-hardened stainless steel.Fully ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with a number of serial number.Built according to DIN...
Square with non-deformable steel leaf.Entirely ground on the faces, of high precision being performed with restricted tolerances.Built according to the DN 875/1 standard.
High precision square with internal bevelled edge.Made of hardened stainless steel.Built according to DIN 875/00 standard.Supplied in scabbard.
PDF TAB
Onglet square in non-deformable steel.With anti-corrosion treatment.This square is equipped with several degrees: in fact, it is possible to measure 90° - 45° - 30° - 120°.Fully ground on the surfaces.Built according...
High precision square in hardened stainless steel.Complete with adjustable rule.In cobalt super-fast steel, ground and HRC hardened 64÷ 65.Provided with angle reading indicator in degrees from –10° / 0° /...
Black granite inspection square, suitable for perpendicularity checks.Highly reliable instrument, thanks to very narrow tolerances and support stability.Lightning holes are drilled on the large squares.The surfaces...
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Bait Guardapiano at 5 blades. Suitable for corrector matrices . in stainless steel, rectified and lapping. built According to DIN 874/0. provided in the case.
PDF TAB
Periphery tape small section in steel for round bodies.The instrument has two scales: the upper one is for diameters and the lower for circumferences.
Angle plate made from G25 perlitic cast iron with T-grooves. Compact and stabilised structure. Closely scraped work surfaces. Manufactured as per DIN 875/3.
English
Italiano 
![](http://pinterest.com/pin/create/button/?url=https%3A%2F%2Fwww.bocchicontrol.it%2Fen%2Fcontrol-rulers-and-squares%2F319-art0517-square-in-cast-iron-with-t-grooves.html&description=ART.0517 - SQUARE IN CAST IRON WITH "T"-GROOVES&media=https://www.bocchicontrol.it/567-large_default/art0517-square-in-cast-iron-with-t-grooves.jpg){kind=link}