Square with non-deformable steel cap.The base made from a single piece and not applied, makes this square very sturdy and suitable for heavy carpentry work.A galvanic treatment protects it from possible oxidation.
PDF...
ART.0510 - PARALLEL SQUARE
Parallel square in non-deformable steel with anti-corrosion treatment.
The stop is hardened to reduce wear to the minimum.
The entire beam is graduated in millimeters with long-lasting incision.
A reference line is etched on the sliding base.
Suitable for scribing, depth and height measurements.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0510
Love0
Add to compare0
20 other products in the same category:
G25 pearlitic cast iron square.Compact and stabilized structure.Fine planed work surfaces.
PDF TAB
Hardened stainless steel knife-edge straight edge for fast and precise control of planarity and parallelism.Made from hardened stainless steel, ground with lapped contact angle.Fitted with heat-insulated...
elbow team for flange in non -deformable steel with antibody treatment. entirely rectified on the faces.
Square with non-deformable steel hat.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment. Built with...
high precision team in stainless steel timing. Complete with square row with 45 ° chamtoe in super-rapid cobalt steel. 65. Suitable for matrici corrector . built according to DIN 875/0. supplied in the case....
Square with non-deformable steel leaf.Entirely ground on the faces, of high precision being performed with restricted tolerances.Built according to the DN 875/1 standard.
Simple set square in non-hardened stainless steel.Fully ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with a number of serial number.Built according to DIN...
Simple 45° square in non-deformable steel.Entirely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Steel ruler with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.Cod. 10 total length 1000 mm as master of length.
High precision square in hardened stainless steel.Complete with 45º bevelled edge beam in super-rapid cobalt steel.Ground and hardened to HRC 64-65.Suitable for a mould checker.Manufactured as per DIN 875/0.Supplied...
High precision square with internal bevelled edge.Made of hardened stainless steel.Built according to DIN 875/00 standard.Supplied in scabbard.
PDF TAB
45° square with stock in non-deformable steel.Entirely ground surfaces.Manufactured as per DIN 875/2.
Bevelled steel ruler with one millimetre graduation.Ground on all faces. Etched, precision graduation, easy to read and long-lasting. Serial number.Manufactured as per DIN 866/1.
Set square with cap in non-hardened stainless steel.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with number serial number.Built according to DIN...
Semi-rigid rulers in mat stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Square with stock in non-deformable steel.Entirely ground faces.High precision.Made to strict tolerances.Manufactured as per DIN 875/1.
Item 421 manufactured as per DIN 875/2.
Square with 120° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Simple square in non-deformable steel.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment.< br...
Simple bevelled square in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground.High precision being performed and tested according to...
English
Italiano 
