High precision square in hardened stainless steel.Complete with adjustable round rule.In 64÷ hardened cobalt super-rapid steel 65 HRC.Suitable for matrix corrector.Manufactured according to DIN 875/0 standard.Supplied...
ART.0520 - ASSEMBLY BLOCK
Assembly box with T-grooves and slots.
Made in G25 stabilised perlitic cast iron.
Squareness between the scraped faces to DIN 875/3 precision.
T-grooves and slots as per UNI 4788.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0520
Love0
Add to compare0
20 other products in the same category:
High precision square in hardened stainless steel.Complete with 45º bevelled edge beam in super-rapid cobalt steel.Ground and hardened to HRC 64-65.Suitable for a mould checker.Manufactured as per DIN 875/0.Supplied...
Square with 60° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Rulers with contraction in mat stainless steel.Division on one side, etched, easy to read and long-lasting.Contractions: 0,5% - 0,8% - 1,25% - 1,5% - 1,7% - 1.75% - 1,8% - 2% - 2,25% - 3% - 4% - 6%.Please specify the...
Square in harendened stainless steel.Large section for greater precision.Ground on all sides.Serial number.Manufactured as per DIN 875/0.Suppilied in case.
Simple set square in non-hardened stainless steel.Fully ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with a number of serial number.Built according to DIN...
High precision plane-parallel control ruler in black granite.Two parallel, plane, lapped faces with << I >> -shaped section for stability and lightness.The parallelism tolerance is equal to the planarity...
elbow team for flange in non -deformable steel with antibody treatment. entirely rectified on the faces.
High precision square with 30° and 45° bevelled edge.Body and edge in hardened stainless steel.Suitable for for metric corrector.Built according to DIN 875/0 standard.Supplied in case.
PDF TAB
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Bait Guardapiano at 5 blades. Suitable for corrector matrices . in stainless steel, rectified and lapping. built According to DIN 874/0. provided in the case.
PDF TAB
Millimeter control line in non-deformable steel.Rectified on all faces.Engraved precision graduation, easy to read, durable over time.Equipped serial number.Built according to DIN 874/1 and DIN 866/1 standards.
PDF TAB
Square with striker and bevel in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.Entirely ground, of high precision being performed and tested according to restricted...
Parallel block in stabilized G26 pearlitic cast iron.Fine planed working surface.
Simple square in non-deformable chromed steel.The square is covered with a uniform layer of hard chrome applied with a special procedure which ensures a high degree of hardness and protection to the surfaces from...
Flat 135° square in non-deformable steel. Entirely ground surfaces. Manufactured as per DIN 875/2.
Precision straight edge in non-deformable steel made to very small tolerances; for precision control situations.Ground on all faces.Serial number.Manufactured as per DIN 874/1.
Square with stock in non-deformable steel.Entirely ground faces.High precision.Made to strict tolerances.Manufactured as per DIN 875/1.
Item 421 manufactured as per DIN 875/2.
high precision team in stainless steel timing. Complete with square row with 45 ° chamtoe in super-rapid cobalt steel. 65. Suitable for matrici corrector . built according to DIN 875/0. supplied in the case....
Bevelled square with hardened stainless steel cap.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground. High precision as it is manufactured and tested according to...
English
Italiano 
