Millimeter control line in non-deformable steel.Rectified on all faces.Engraved precision graduation, easy to read, durable over time.Equipped serial number.Built according to DIN 874/1 and DIN 866/1 standards.
PDF TAB
ART.0400 - METRIC TAPE MEASURE WITH TAPE IN STEEL DA CF-758/10 A CF-758/50
Square in harendened stainless steel.
Large section for greater precision.
Ground on all sides.
Serial number.
Manufactured as per DIN 875/0.
Suppilied in case.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0400
Love0
Add to compare0
20 other products in the same category:
Bevelled ruler in non-deformable steel with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.
Simple square in non-deformable steel.Completely ground on the faces.High precision being performed with tight tolerances.Built according to DIN 875/1 standard.
Art. 420 built according to the DIN 875/2 standard.
PDF TAB
Cube for radial drills in stabilized G26 pearlitic cast iron.Properly ribbed to ensure strength.Fine planed working surface with “T” grooves.
Square with non-deformable steel cap.The base made from a single piece and not applied, makes this square very sturdy and suitable for heavy carpentry work.A galvanic treatment protects it from possible oxidation.
PDF...
Simple 60° square in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
Angle detector and bisector.Consisting of an adjustable part in which, by means of a line of faith and an engraved and easy-to-read graduated rod, it can be detected or set the desired angle and a removable part...
Parallel block in stabilized G26 pearlitic cast iron.Fine planed working surface.
Square with 120° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Simple bevelled square in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground.High precision being performed and tested according to...
Square with tempered stainless steel striker.Completely ground, of high precision as it is performed and tested according to restricted procedures.The serial number is engraved which guarantees its traceability.Built...
elbow team for flange in non -deformable steel with antibody treatment. entirely rectified on the faces.
Simple steel square with anti-corrosion galvanic treatment.Being machined from solid, it allows for two 45° angles and one 90°.Entirely ground surfaces.
Square with striker and bevel in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.Entirely ground, of high precision being performed and tested according to restricted...
Sliding square in non-deformable steel with anti-corrosion treatment.Suitable for the transfer of angles.
flat and adjustable magnetic teams .
are indispensable for welding or tracks where a 90 ° position is needed.
Simple square in hardened stainless steel.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with serial number.Built according to DIN 875/0...
High precision square in hardened stainless steel.Complete with adjustable round rule.In 64÷ hardened cobalt super-rapid steel 65 HRC.Suitable for matrix corrector.Manufactured according to DIN 875/0 standard.Supplied...
High precision square with 30° and 45° bevelled edge.Body and edge in hardened stainless steel.Suitable for for metric corrector.Built according to DIN 875/0 standard.Supplied in case.
PDF TAB
Square with 135° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
English
Italiano 
